Bmw Sport Roadster

Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076

Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076

Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076

Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076. The description of this item has been automatically translated. Suitable for the following vehicles.

Vehicle: BMW Z4 Roadster Type: Z 85 Construction year: from 12.02 -> Lowering: VA: approx. 30 mm max axle loads: VA: 790 kg, HA: 840 kg Notes: 1, 21. Are you not sure whether the springs fit your vehicle? Please inquire with us with the corresponding vehicle data. Additional note: 1 = The amount of lowering is reduced by the amount of lowering at the factory. 21 = All wheel / tire combinations approved by the wheel test centers can be used. The requirements in the wheel report or Wheels ABE must be complied with, with the exception of the requirement for standard chassis.

With VOGTLAND sport spring sets - - upgrade your vehicle: r. Asante optics with maximum driving pleasure.

Whether in normal operation with pleasant driving comfort or in the limit area with sporty progressive tuning. The special driving dynamics are achieved through the innovative spring design. The shortening of the spring travel requires a special suspension characteristic. Which is derived from racing. The VOGTLAND compound spring consists of two different spring rates.

A start and an end rate. These specially tailored to your vehicle type. Characteristic curves that interact with one another stand for balanced driving comfort and greater driving dynamics, even with a sporty driving style.

The lowering ranges from 25 to 60 mm. Increase agility and driving fun and experience your vehicle in a completely new way! Lower the front axle a little lower than the rear axle. And you will be amazed how your vehicle is transformed into a visual power package thanks to the particularly dynamic wedge shape. E with only two springs for the front axle. The amount of lowering is reduced by the amount of lowering at the factory. The measure of the lowering will be reduced by the measure of the sport suspension. Wedge shape: The lowering of the front axle depends on the equipment and engine variant. Wedge form: The lowering of the front axle depends on the equipment and weight of the engine.

For fine-tuning, please use Mercedes-Benz spring plate pads, which are available in different thicknesses (8 - 23 mm). For fine tuning, please refer to the Daimler Benz spring insolators available in different heights (8-23 mm). Reinforced version (heavy duty) for vehicles with full equipment and more than 4 cylinders. Heavy duty for models with full equipment and more than 4 cylinders.

For vehicles with a load-dependent brake force distributor, a demonstration is required despite the ABE. A presentation is necessary despite ABE for vehicles with a load depending on brake power distributor.

Not for vehicles with level control / air suspension. Without self-leveling / air suspension.

In vehicles with Tiptronic, Multitronic, increased lowering possible. Additional lowering may occur on vehicles equipped with automatic transmissions. Only for vehicles with full equipment.

With the XR3i no additional lowering, just tighter tuning. XR3i does not lower, only the adjustment becomes more sportive. For vehicles with 6 cylinders, e. Golf III VR6, conversion to sports dampers is recommended, which is included in the VOGTLAND complete chassis. Vehicles with 6 cylinder engines require sport shocks.

Not for: Break, Caravan, Tournament, T-Model, Touring, Variant, Avant, Station Wagon, Traveler, (station wagon). As of ABE number 9138/2. Use spring plates with the no.

171412341A up to 8.79. Up to 8.79 please use spring cap number 171412341A. Modified spring plates [and possibly other parts] must be used on the front axle. Either the spring plate with VW part number 1H0412341 (large) or 357 412 341 A (small). Volkswagen springs caps [and probably further parts] might be necessary: 1H0412341 (big) or 357412341 A (small). Shortened sport shock absorbers required. These are already included in the VOGTLAND complete chassis. Shorter sport shocks are required. The VOGTLAND suspension kits are covered with these shocks. Not for series sports suspensions. Not suitable for serial or sport suspension. Only front axle springs, rear axle torsion bars (or standard spring element). Only front springs, torsion bars (or standard spring) on the rear axle.

Only rear axle springs, front axle torsion bars (or standard spring element). Only rear springs, torsion bars (or standard spring) on the front axle. All wheel / tire combinations approved by the wheel test centers can be used.

All wheel / tire combinations are allowed which are released by the wheel type testing institution. The conditions in the wheel approval have to be kept, except when suspension is required. With adjustable complete chassis, the damping forces can only be adjusted on the front axle when installed. At the VOGTLAND adjustable suspension kits are only the shock valvings in the front adjustable. Due to vehicle-specific tolerances, it is possible that the stabilizer and drive shaft touch each other. For coilover kit: Item no. 968550000, stabilizer kit, without xenon. For complete chassis: elongated series coupling rods (VW / Audi). Due to vehicle-specific tolerances a contact between the drive shaft and the anti-roll bar might occur. In such case it is required to install a modified anti-roll bar. For coilover sets use Order-No. 968 550 000 (Anti-roll bar conversion set without Xenon headlights).

For suspension kits use a longer steering rod from your VW / Audi dealer. VA / HA coilover struts (height adjustable). Height adjustable at the front and rear axle (threaded strut housings). VA / HA height adjustable VA coilover struts, HA springs with height adjustment plus.

Height adjustable at the front and rear axle (front axle threaded housings, rear axle threaded spring perch and separate shocks). Only VA height adjustable, HA spring and shock absorber. Only height adjustable at the front axle (threaded strut housings), springs and shocks at the rear axle. With series tires possibly Spacers required. May require the use of wheel spacers with equipment tires and wheels. The level control must be shut down. Self-leveling must be shut down.

VA height-adjustable coilover strut, HA sport shock absorber (HA adjustment via torsion bar). Height adjustable at the front (threaded strut housings), rear axle is adjustable with torsion spring adjustment. Installed shocks can be adjusted when installed.

Damper can only be adjusted when removed. Installed shocks cannot be adjusted when installed. The front direction indicators (§ 76/756 EG) must maintain a minimum height of 350 mm. The front turn lights (§76 / 756 EG), must be the min. Production date 4/02 (piston rod thread visible), from 4/02 (piston rod thread covered). Fore vehicles manufactured before 04/02, the piston rod is fastened to the support bearing with an arched disk (piston rod threads visible). Models built after 04/02, piston rod threads not visible.

Use only for vehicles with rear shock absorber mount attachment M10 (1.0i, 1.2i, 1.7Di). Only for vehicles which have rear dampers mounted below with M10 (1.0i, 1.2i, 1.7Di). Use only for vehicles with rear damper mount attachment M14.

(1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). Only for vehicles which have rear dampers mounted below with M14 (1.4i, 1.8i, 1.3CDTI, 1.7DTi, 1.7CDTi). VA shock absorber: complete strut with item no. 960422, 960423, 966322, 966404, 966406, 966407, 969419, 969422, 969423, 960462.

Front shock: complete suspension strut. Partnumber: 966404, 966406, 966407, 966322, 960422, 969423, 960423, 960462. VA shock absorber: strut cartridge.

Dampers are only suitable for European vehicles. Damper only siutable for European Cars. If the drive shaft diameter is more than 42 mm, the max. If the driveshaft diameter is greater than 42, mm the max.

Aproved lowering is reduced 15 mm. The inner distance on the front suspension strut (between the fastening straps) must be 27 mm. The inside distance between the mounting bracket of the front damper must be 27 mm. From chassis number Y-an on 10. From chassis number Y on the 10th position. For vehicles with 50 mm strut. For cars with 50 mm suspension strut.

For vehicles with 55 mm strut. For cars with 55 mm suspension strut. For vehicles from year of manufacture 10.91 to 5.92, the upper mounting bearings BMW - No.

For cars built from October 1991 up to May 1992 the upper attachment must be replaced by BMW partnumber 31.331.090.467. Until 1998 (up to chassis number 8DX199999). Up to 1998 models (up to VIN: 8DX199999). Coupling rods 968220, 968221 required for lowering over 40 mm. Steering rod 968220, 968221 for lowering above 40mm nessecary.

After the chassis has been installed, it can move freely Check the tires for the VA shock absorber min. 5 mm and possibly by means of to restore tested spacers. After mounting the clearance between the wheel and suspension strut must be at least 5mm. If it is smaller you have to use wheel spacers. Audi: year of manufacture up to 4.00, VW: year of manufacture up to 9.99. Audi: Modelyear up to 4.00, VW: Modelyear up to 9.99. Audi: year of manufacture from 5.00, VW: year of manufacture from 10.99.

Audi: Modelyear after 5.00, VW: Modelyear after 10.99. Without 16V, VA mounting hole spacing 52 mm. Without 16V, front bracket bolt distance 52 mm. Without 16V, VA mounting hole spacing 54 mm.

Without 16V, front bracket bolt distance 54 mm. Without rally, TD, Genty, CT, CTI, GTI.

Without Rallye, TD, Genty, CT, CTI, GTI. Year of construction up to 8.04, without 2.0T, 3.0V6 CDTi, without IDS. Modelyear up to 08.04, without 2.0T, 3.0V6 CDTI, without IDS. From model year 8.04, without 2.0T, 3.0V6 CDTi, without IDS. Modelyear after 08.04, without 2.0T, 3.0V6 CDTI, without IDS.

For vehicles with eye attachment on the rear axle. For models with eye-mounting at the rear. For vehicles with fork mounting on the rear axle. For models with fork mounting at the rear. Not for vehicles from model year 2004. Not for models built after 2004. VA shock absorber check the dimensions of the mounting brackets: hole spacing 52 mm; Distance dimension 23 mm. On front shock check measurements for the bracket: inside width 23 mm, mounting hole distance 52 mm. Only for vehicles with all-wheel drive (4WD). Only for cars with four wheel drive (4WD).

Dome bearing 31331091709, disc 31331116983, sleeve 31331110196, rear BMW part no. Support bearing 33521091710, support pot 33521090282, disc 33521092986, protective tube 31331137 932, elastomers 33531091031. Additional OE equipment is needed on cars with EDC.

Engines BMW part number: Bearing 31331091709, Washer 31331116983, Dust Cap 31331110196. Rear BMW part number: Bearing 33521091710, 33521090282, Washer 33521092986, Dustseal 31331137 932, Bumpstop 33531091031. Sport damper (included) in connection with standard air spring on the rear axle.

The OE-air suspension is not removed. A rear sport shock is provided and used with the air suspension. Not for vehicles with electronic damper adjustment.

Not for vehicles with electronic damping adjustment. For Allen vehicles before Bj. 6/92, basically changed cathedral bearings must be used.

Dome bearing 31336764947, washer 31331116983, sleeve 31331110196. For all cars built before 6/92 the use of different top-bearing assembly in the front is required.

BMW part number: Bearing 31336764947, Washer 31331116983, Dustseal 31331110196. Damping force regulation, without IDS +. Damping force adjustment, without IDS +. Shock absorber bearing 8E0512121E, spring pad 8E0512149H, stop buffer 4B0512131Q. For cars with self-leveling additional OE-parts are required: Audi Partnumber: Bearing 8E0512121E, Springseat 8E0512149H, Bump stop 4B0512131Q.

Model specific plug & play adapter included. Hardness adjustment only on the VA. Model specific plug & play adapter available as an option.

Only for vehicles with air suspension. Only for Cars with Air Suspension. Only for vehicles with ABC chassis. Only for Cars with ABC Suspension.

From chassis number: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6 & 74337, USA V6: 4LA21527. From VIN: Turbo: 4LA83740, S: 4LA48416, V6: 4LA01526, USA Turbo: 4LA93466, USA S: 4LA6 & 74337, USA V6: 4LA21527. Only for multi-link rear axle. Only for Multilink rear suspension. Only for twist beam rear axle.

Only for twist-beam rear suspension. For vehicles with an individual operating permit (EBE), an acceptance according to §21 StvZo (individual acceptance) is required. Sets without available as an export item. For Cars with a single operating permit (EBE) an approval regarding §21 StvZo is required. Sets without can be ordered for the export market. Comments in brackets only apply to complete trolleys. Remarks in brackets only for kits. We reserve the right to make technical changes. We do not accept any liability for misprints.

Subject to possible technical revisions. Reserves the right to change product specifications. We do not assume liability for misprint. We are happy to answer any questions you may have.

Monday to Thursday: 8 a. List your articles quickly and easily and manage your active offers. 1 = The amount of lowering is reduced by the amount of lowering at the factory. The item "Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076" is in sale since Friday, November 8, 2019. This item is in the category "Vehicle Parts & Accessories\Car Tuning & Styling\Performance Suspension\Lowering Springs & Kits". The seller is "pbt-racing" and is located in Grafenwiesen. This item can be shipped to all countries in Europe.
  • Manufacturer: Vogtland
  • Manufacturer Part Number: 951076
  • Brand: Unbranded

Vogtland Lowering Springs BMW Z4 Roadster Z85 30mm 951076